Venturi Blast Nozzles
Showing all 12 results
-
- Replacement silencers for the SnakeBite family of blast nozzles
- Up to 45% less operator fatigue
- Up to 16dB noise reduction
- 2 versions available
- Standard Pressure Silencer effective between 90-110 psi
- Low Pressure Silencer (LPS) effective between 70-90 psi
-
- Industry Leading Blast Nozzle
- SiNi II grade silicon nitride liner
- Shock absorbent, lightweight urethane jacket protects the blast nozzle liner
- Vacuum molded urethane thread – reduces ‘jams’ in nozzle holder
- Half the weight of conventional tungsten carbide abrasive blast nozzles
- 2" UNC (50mm) coarse Contractor thread or 1-¼" Fine Thread
- 1¼" (32 mm) wide throat entry, long venturi – except Ultra-3 & Ultra-4 have 1" (25 mm) throat entry
-
Standard Tungsten Carbide (aka TVP) blast nozzles are widely used and are a low-cost, basic general-purpose nozzle with the following characteristics:
- Industrial-strength tungsten carbide liner.
- Venturi design offers higher performance than straight bore.
- Comes in 3 configurations:
- 1-1/4" NPSM (32mm) fine threads
- 2" (50mm) contractor threads
- Flange type (unthreaded, and attaches to a blast hose with a standard blast hose quick coupling instead of a nozzle holder)
- 1" (25mm) wide throat entry for #3 and #4 sizes
- 1 1/4" (32mm) wide throat entry, for all other sizes
- Stocked in brass threads w/polyurethane jacket. All Poly available upon request.
- Lowest up-front cost of any standard industrial blast nozzle.
- Higher in weight and less shock-resistant than other types.
- Lower total cost of ownership, higher performance, and/or improved ease-of-use may be achieved with one of the premium nozzle options. See You May Also Like below.
-
- Extra-long venturi and concentrated blast pattern increases performance by up to 30% on coating removal projects
- 2" UNC (50mm) Contractor thread
- 1¼" (32mm) wide throat entry, extra-long venturi
- Also known as Saber or XL nozzle
- SiALON II grade silicon nitride liner
- Aluminum jacket and thread with urethane cushioning
- Non-slip knurl makes it easy to hold onto for the blaster
- Available for Rental or Purchase
- Sold Individually
-
Designed with a 60% larger blast pattern, the Raptor (aka Bazooka) nozzle makes short work of your large commercial blast / sweep blast / brush blast projects. Additional details as follows:
- Thread types:
- Contractor (2") aluminum threads
- Fine (1-¼") brass threads
- Liner:
- Silicon nitride, offers lighter weight and longer life than tungsten carbide.
- Jacket:
- Urethane, for improved resistance to damage
- Design:
- 1-¼" throat entry, extended venturi
- Thread types:
-
These medium thread nozzles have a longer venturi than the BNAT nozzle series, making them ideal for use in our RotorBlast internal pipe blaster (when blasting pipe 12" in diamater or greater). Available in multiple orifice sizes. When using them in pairs (like when using in the RotorBlast), be sure to calculate your compressor CFM size requirement accordingly.
-
- 2" UNC (50mm) coarse Contractor thread 'C' or 1 1/4" NPSM (32mm) Fine Industrial thread 'F'
- Square thorat entry, venturi
- Tungsten carbide liner
- Urethane jacket, brass thread
- Large square blast pattern - less overlap when blasting
- Alignment ridges on jacket
-
- 3/4" NPSM (20mm) 'M' Medium thread
- 1/2" (13mm) throat entry
- Tungsten carbide liner
- Aluminum jacket and thread
- Very short - 1-5/8" long
- Commonly used with Internal Pipe RotorBlast when blasting pipes between 8 and 11 inches in diameter, or in other hard-to-reach blasting areas
- Uses HFGFBSP nozzle washers (not included) - order separately
-
BNATLW3C
- 2" UNC (50 mm) coarse Contractor thread
- 1 1/4" (32 mm) wide throat entry, long venturi
- Tungsten carbide liner
- 'The Original' Contractor favorite
- Standard weight aluminum jacket and thread
- Use HF G32P nozzle washes (not included - order separately)
BNATLW3C- 2" UNC (50 mm) coarse Contractor thread
- 1 1/4" (32 mm) wide throat entry, long venturi
- Tungsten carbide liner
- 'The Original' Contractor favorite
- Standard weight aluminum jacket and thread
- Use HF G32P nozzle washes (not included - order separately)
-
- Suits 1 1/4" blast hose
- Durable steel jacket
-
INH131PBAGThe “Blast Nozzle Wear Size Analyzer Gauge” (SKU: INH131PBAG) efficiently determines the internal diameter and wear level of a blast nozzle orifice, ensuring optimal blasting performance.
- Used to determine the internal diameter of a blast nozzle orifice
- Allows you to determine the level of wear of the blast nozzle
- Comes with a removable cap and crayon
- Has size markings to allow you to see quickly what size your nozzle is
- Sold Individually
INH131PBAGThe “Blast Nozzle Wear Size Analyzer Gauge” (SKU: INH131PBAG) efficiently determines the internal diameter and wear level of a blast nozzle orifice, ensuring optimal blasting performance.- Used to determine the internal diameter of a blast nozzle orifice
- Allows you to determine the level of wear of the blast nozzle
- Comes with a removable cap and crayon
- Has size markings to allow you to see quickly what size your nozzle is
- Sold Individually