My Account
Heavy Duty Sand & Abrasive Blast Nozzles
Showing 16–30 of 35 results
-
Short nozzles with straight bore are made for close-range spot blasting. The blast pattern is small, making it ideal for cleaning small areas, railings, etc. Other details as follows:
- Fine thread, 1-¼" - 11-½" NPSM
- Available in sizes from #3 to #8
- Tungsten carbide liner
-
Short venturi nozzles are made for close-range blasting. The venturi allows the widest possible pattern in limited space environments. Other details as follows:
- Available in either Contractor thread (50mm) or Fine thread (1-¼")
- Available in orifice sizes from #3 to #12
- Tungsten carbide liner
- Multiple jacket types available
Call / chat / email us if the version you are looking for is not shown.
-
- Used for blasting pipe internals with 3"-12" ID
- Blasts in a 360 degree pattern
- Units come standard with Tungsten Carbide deflector tip
- Select the unit that will best match your Air Supply:
- IPC4000, 1/2" Throat Nozzle: 250 cfm
- IPC4500, 5/8" Throat Nozzle: 400 cfm
- Order Transport Carriages separately as follows:
- IPC4100, Collar and Button, for 3"-5" ID
- IPC4200, Scissor, for 5"-12" ID
- Requires BSP (not NPT) threaded coupling to attached to standard blast hose coupling, part number HFSTC1BSP, available here or under the repair parts tab below.
- Successful Internal Pipe Projects require some specialist knowledge - contact our team for assistance
- Note: This product is similar to the Clemco Hollo-Blast
-
These medium thread nozzles have a longer venturi than the BNAT nozzle series, making them ideal for use in our RotorBlast internal pipe blaster (when blasting pipe 12" in diamater or greater). Available in multiple orifice sizes. When using them in pairs (like when using in the RotorBlast), be sure to calculate your compressor CFM size requirement accordingly.
-
VCBV104- Suits Blast and Vac Workhead BNV-3/VCBV200 (Standard Unit)
- Nozzle Internal Venturi 1/4" #4 Long Venturi
- Long Lasting
- Sold Individually
VCBV104- Suits Blast and Vac Workhead BNV-3/VCBV200 (Standard Unit)
- Nozzle Internal Venturi 1/4" #4 Long Venturi
- Long Lasting
- Sold Individually
-
Tite-Space nozzles are angle nozzles, designed for use in areas that are especially difficult to access, and feature:
- 3/8" NPT Thread in either Male or Female configuration
- Male version has brass threads and requires a minimum opening clearance of 1". This version is 1-7/8" long.
- Female version has steel threads and requires a minimum opening clearance of only ¾". This version is 3-1/8" long.
- These nozzles are often used in conjunction with our Tite Space Invader Blasting Kit, available here
- Angle options include:
- 45° & 60° forward blast
- 90° right angle blast
- 135° reverse blast
- Some options available in double, triple or quad orifices in addition to single.
- Note: Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly.
- Stock version uses tungsten carbide lining.
Note: Due to the angled blast stream, these nozzles will wear more quickly than traditional versions. For larger projects, we offer long-life Roctec nozzle linings by special order, with a minimum order quantity of 5. Contact us for further details.
-
- 2" UNC (50mm) coarse Contractor thread 'C' or 1 1/4" NPSM (32mm) Fine Industrial thread 'F'
- Square thorat entry, venturi
- Tungsten carbide liner
- Urethane jacket, brass thread
- Large square blast pattern - less overlap when blasting
- Alignment ridges on jacket
-
Sized between the Tite Space and the full size nozzles, the ATA series of angle nozzles come standard with ¾" Medium Threads. They are excellent for applications requiring the operator to operate in small areas, especially when paired with a small bore whip-hose. Basic specs are:- 3/4" (20mm) Medium male thread (other options available by special order). Can be used in standard Fine or Coarse nozzle holders by use of a thread adapter available here.
- 1/2" (13mm) throat entry
- 45° forward, 90° right angle, and 135° reverse blast pattern options available
- Some sizes are available in Double, Triple or Quad orifices
- Note: Using nozzles with multiple orifices will multiply the compressed air CFM requirement accordingly
- Tungsten carbide liner. Extended life liners for large projects available by special order.
- Short 2-1/8" length
-
BNATC360COffers Quick and Easy Setup for blast cleaning on internals of small pipes- Blasts in a 360 degree pattern
- Can be used in pipes from 2.5 to 5 inch ID
- Machined aluminum jacket with tungsten carbide liner
- Replaceable tungsten carbide deflector tip
- Coarse, 2" Contractor Thread
- Screws directly into nozzle holder
- NOTE - requires Nylon nozzle holder with contractor threads
BNATC360COffers Quick and Easy Setup for blast cleaning on internals of small pipes- Blasts in a 360 degree pattern
- Can be used in pipes from 2.5 to 5 inch ID
- Machined aluminum jacket with tungsten carbide liner
- Replaceable tungsten carbide deflector tip
- Coarse, 2" Contractor Thread
- Screws directly into nozzle holder
- NOTE - requires Nylon nozzle holder with contractor threads
-
- 3/4" NPSM (20mm) 'M' Medium thread
- 1/2" (13mm) throat entry
- Tungsten carbide liner
- Aluminum jacket and thread
- Very short - 1-5/8" long
- Commonly used with Internal Pipe RotorBlast when blasting pipes between 8 and 11 inches in diameter, or in other hard-to-reach blasting areas
- Uses HFGFBSP nozzle washers (not included) - order separately
-
FAN BLAST™ Fan Pattern SiALON Blast Nozzles give wide, even blast patterns, ideal for sweep blasting. Different variations include:
- 2" UNC (50mm) coarse contractor thread
- 1-1/4" ( N.P.S.M.) fine industrial thread
Also available with tungsten carbide liner - enquire for price and lead time.
At present, this nozzle is available only with a #6 orifice. An alternative nozzle type for this application, which is available in multiple orifice options, is the Raptor / Bazooka nozzle.
-
BNATLW3C- 2" UNC (50 mm) coarse Contractor thread
- 1 1/4" (32 mm) wide throat entry, long venturi
- Tungsten carbide liner
- 'The Original' Contractor favorite
- Standard weight aluminum jacket and thread
- Use HF G32P nozzle washes (not included - order separately)
BNATLW3C- 2" UNC (50 mm) coarse Contractor thread
- 1 1/4" (32 mm) wide throat entry, long venturi
- Tungsten carbide liner
- 'The Original' Contractor favorite
- Standard weight aluminum jacket and thread
- Use HF G32P nozzle washes (not included - order separately)
-
- Ideal for blasting recesses, pipe internals, behind angles, lattices etc.
- 2" UNC (50mm) coarse Contractor thread 'C' or 1 1/4" NPSM (32mm) Fine Industrial thread 'F'
- 3/4" (20mm) throat entry
- 45° single, double or triple (equi-spaced) side outlets
- Tungsten carbide liner
- **Triple orifice nozzles have triple air & abrasive consumption!
-
VCBVRA4- #4 Nozzle
- 90 degree
- Tungsten Carbide
- For Right Angle Workhead
VCBVRA4- #4 Nozzle
- 90 degree
- Tungsten Carbide
- For Right Angle Workhead
-
- Suits 1 1/4" blast hose
- Durable steel jacket
A TIP ON WHEN TO REPLACE YOUR SAND BLAST NOZZLE
Even a very small increase in blasting nozzle size will result in a very large increase in ‘air and abrasive consumption’. When a sand blast nozzle has worn 1/16” (2mm) larger, it is time to be replaced. Use an abrasive blast nozzle size analyzer kit to check your nozzle regularly (we recommend at least ONCE PER WEEK). You’ll be surprised how much your production decreases with a worn sand blasting nozzle! Wet blasting & WIN (Water Induction Nozzles) also available
SANDBLASTING NOZZLES & ABRASIVE BLAST NOZZLES
NOTE: Efficiency drops 1.5% for every 1 psi below 100 at the sand blasting nozzle. This means a 14% efficiency drop at 90 psi, 26% efficiency lost at 80 psi and almost half lost at 60 psi. Efficiency goes up as pressure increases. 120 psi improves performance by 30%. Actual efficiency increase/ decrease will vary depending on abrasive type and size, blast nozzle type, size and wear, hose sizes and wear, temperature, moisture content of compressed air, etc. Use a abrasive wet or dry blast nozzle pressure gauge to measure air pressure at the nozzle. Make allowance for increased air consumption due to sandblast nozzle wear, air leaks, breathing airline filter, respirator breathing air and any pneumatic equipment using air from the compressor. A good rule of thumb is to use a compressor twice the capacity of the grit blast nozzle consumption.
