My Account
Blasting
Showing 46–60 of 945 results
-
This general-purpose nozzle was designed for everyday use, only better - it lasts longer and offers greater ease of use! It features the following:
-
Performance characteristics:
- Venturi design provides up to 40% faster production than straight bore versions.
-
Thread type & Orifice Size options:
- Contractor 2" (50mm)
- Fine 1-¼" (32mm)
- Orifice size options: 3, 4, 5, 6, 7, 8
-
Liner:
- Silicon nitride, provides longer life and lighter weight than tungsten carbide.
-
Jacket:
- All-polyurethane – reduces ‘jams’ in metal nozzle holders
- Shock absorbent, lightweight urethane jacket protects the blast nozzle liner
-
Design:
- 1" throat entry on #3 and #4 Contractor thread AND all Fine thread options
- 1-¼" throat entry on #5, 6, 7, and 8 Contractor threads
-
Additional notes:
- Approximately half the weight of standard tungsten carbide nozzles.
- Although the up-front cost is higher than tungsten carbide, the longer life Ultra-Tuff offers same or better total cost of ownership.
-
Performance characteristics:
-
The blast nozzle for the ConeBlast Internal Pipe Blaster is a key element in controlling the volume of air/abrasive flow. It is subject to high wear and is a common replacement part. Additional details:
- Sizes. Two sizes are available, depending on the capacity of your compressed air source.
- BNAFR8 requires 250CFM
- BNARF10 requires 400CFM
- (The size variants are interchangeable.)
- Construction. These nozzles are made from tungsten carbide. For large pipe-cleaning projects, contact us for options on longer-life versions.
- Sizes. Two sizes are available, depending on the capacity of your compressed air source.
-
Designed with an extra-long venturi and concentrated blast pattern, the Hyper (aka XL or Saber) nozzle increases performance substantially. Additional details as follows:
-
Performance characteristics:
- Up to 30% faster coating removal and/or
- Allows greater stand-off distance (reduces need to bend over when blasting tank floors, allows greater reach, etc.)
-
Thread types & Orifice Size options:
- Contractor 2" (50mm)
- Fine 1-¼" (32mm)
- Orifice size options: 5, 6, 7, 8, & 10
-
Liner:
- SiALON silicon nitride, provides longer life and lighter weight than tungsten carbide.
-
Jacket:
- All aluminum, non-slip knurled finish
-
Design:
- 1-¼" throat entry, extended venturi, 12 inches long
-
Performance characteristics:
-
Designed with a 60% larger blast pattern, the Raptor (aka Bazooka) nozzle makes short work of your large commercial blast / sweep blast / brush blast projects. Additional details as follows:
-
Thread types:
- Contractor (2") aluminum threads
- Fine (1-¼") brass threads
-
Liner:
- Silicon nitride, offers lighter weight and longer life than tungsten carbide.
-
Jacket:
- Urethane, for improved resistance to damage
-
Design:
- 1-¼" throat entry, extended venturi
-
Thread types:
-
Standard Tungsten Carbide (aka TVP) blast nozzles are widely used and are a lower-cost, basic general-purpose nozzle with the following characteristics: Click for Buying Guide
- Performance characteristics:
- Venturi design offers up to 40% greater production than straight bore.
- Thread Types:
- 1-1/4" NPSM (32mm) brass fine threads
- 2" (50mm) aluminum contractor threads
- Flange type (unthreaded, and attaches to a blast hose with a standard blast hose quick coupling instead of a nozzle holder)
- Orifice Sizes:
- Contractor & Fine: 3, 4, 5, 6, 7, 8, 10, 12
- Flanged: 6, 7, 8, 10, 12
- Liner:
- Tungsten Carbide, provides longer life than disposable alternatives for industrial blasting projects
- Jacket:
- Contractor and Fine thread versions have poly jacket
- Flanged type is an all-aluminum jacket
- Design:
- 1" (25mm) throat entry for #3 and #4 sizes
- 1 1/4" (32mm) throat entry, for all other sizes
- Additional notes:
- Lowest up-front cost of any industrial blast nozzle.
- Higher weight and shorter lifespan than premium silicon nitride versions.
- Lower total cost of ownership, higher performance, and/or improved ease-of-use may be achieved with one of the premium nozzle options. See You May Also Like below.
- Performance characteristics:
-
The Water Induction Nozzle (aka WIN nozzle) is an economical way to enter the wet blasting market. Commonly used in smaller projects, it offers excellent water flow control. Additional Details:
- Use with standard dry blasting equipment. No modifications required.
- Connects to standard garden hose, or you can use a tank with a standard 12v pump if you need to add rust inhibitor to the water.
- Typically stocked with tungsten carbide liner and contractor threads, it is also available with silicon nitride liner and/or fine threads. Contact us for details.
-
- Curved "Banana" Blast Nozzle
- Made from Boron Carbide which is the longest lasting material used for blast nozzles
- Size listed is a #6, which is 3/8" internal diameter
- Has a Medium 3/4" Thread - Requires a special nozzle holder adapter
- Search for “nozzle thread adaptors” to select an adaptor to use with your existing nozzle holder, or contact BlastOne if you want a medium thread nozzle holder.
- Sold Individually
-
Effective solution for blasting in hard-to-reach areas such as:
- Inside of bolt holes
- Inside of close-fitting steel channels
- Difficult access structural steel, such as bridge supports, etc.
- Offers standard extension lengths from 10 to 60 inches, with other options available by special order.
- Can be used with most abrasives
- Attaches to blast hoses with standard 2-prong couplings (not nozzle holders)
- Nozzle is NOT included and shown for illustration purposes only. Requires junior size 3/8" NPT threaded nozzles. Choose the correct one for your application from our Tite-Space nozzle selection here.
- Female version requires only ¾" clearance.
- Male version requires only 1" clearance.
-
GRACO® SPECIAL PURCHASE - ECOQUIP FINAL CLEARANCE! These hoses and nozzles are top quality new condition, and work on all abrasive blasting equipment (not just EcoQuip). These special-purchase products include the following:
- EcoQuip “Replacement” blast hose assemblies, which include coupling / nozzle holder, control line, and a Schmidt® Response deadman handle, in both pneumatic and electric.
- EcoQuip “Extension” blast hose assemblies, which include couplings and control line, in both pneumatic and electric.
- EcoQuip "Bulk Hose", 50' sections of blast hose, without any accessories
- Graco blast nozzles in the following types:
- Standard (contractor thread)
- Hyper (contractor thread)
- SST (medium thread)
- Double Venturi (contractor thread)
-
Short nozzles with straight bore are made for close-range spot blasting. The blast pattern is small, making it ideal for cleaning small areas, railings, etc. Other details as follows:
- Fine thread, 1-¼" - 11-½" NPSM
- Available in sizes from #3 to #8
- Tungsten carbide liner
-
Short venturi nozzles are made for close-range blasting. The venturi allows the widest possible pattern in limited space environments. Other details as follows:
- Available in either Contractor thread (50mm) or Fine thread (1-¼")
- Available in orifice sizes from #3 to #12
- Tungsten carbide liner
- Multiple jacket types available
Call / chat / email us if the version you are looking for is not shown.
-
BlastOne offers a full selection of industrial fittings. This group is the Hose Barb x Female Pipe Swivel (Ball Seat). Other information is as follows:
- Hose Barb (aka Hose tail) x NPSM FPX Female Swivel
- aka “Nut and Tail”
- First dimension is hose ID for hose barb
- Use with crimp ferrules or worm gear clamps
- Applications: Low Pressure SAE general service air, water, and hydraulic hose
- Operating Pressure Range: 250 PSI maximum at 72F
- Operating Temperature Range: -40 to 160F at 150 PSI max
-
BlastOne offers a full selection of industrial fittings. This group is the Hose Barb x Male Pipe NPTF brass fittings. Other information is as follows:
- Hose Barb x Male Pipe NPTF (first dimension is the hose ID for the hose barb)
- Use with crimp ferrules or worm-gear clamps
- Applications: Low Pressure SAE general service air, water, and hydraulic hoses
- Operating Pressure Range: 250 PSI Maximum at 72F
- Operating Temperature Range: -40F to 160F at 150 PSI Max.
-
BlastOne offers a full selection of industrial fittings. This group is the Male Thread Swivel x Push-Lock Hose Barb. Other information as follows:
- Push-on Hose Barb (aka Hose tail) x NPTF Male Thread Swivel (First dimension is the hose tail size)
- Not intended for use with crimp ferrules or worm clamps
- Yellow plastic cap
- Applications: Compatible with air, most fluids, and low-pressure hydraulic hoses that are push-lock type
- Operating Pressure Range: 120 PSI maximum
Operating Temperature Range: -40°F to 150°F
-
- Female Pipe Coupling
- FP x FP
- Solid Machined Brass
- Performs to SAE J530 and J531 Standards
- Working Pressure: 1,000 PSI
- Temperature Range: -65°F to +250°F
